وكالة
BYD Atto 3
شفّاط التوجيه الخلفي الأيمن - حزمة ما بعد البيع
أكواد OE / المواد
14735239-00SC2EM-2404201HW$83USD
متوفرماذا يحدث بعد ذلك:
- راجع اختياراتك في صفحة السلة.
- ادفع مباشرة عبر Stripe (عندما تكون كل العناصر بأسعار التجزئة).
- أو أرسل القائمة كطلب عرض سعر للجملة.
المواصفات الفنية
- موديل السيارة
- BYD Atto 3
- تكوين التوجيه
- مقود يسار ومقود يمين
الشحن والإرجاع
شحن عالمي من الصين جواً أو بحراً. التسليم القياسي 5–30 يوم عمل، السريع 2–10 أيام عمل. تحسب تكلفة الشحن عند الدفع.
نافذة إرجاع 7 أيام للقطع غير المستخدمة في عبوتها الأصلية. تواصل معنا قبل إرجاع أي قطعة.
السيارات المتوافقة — شفّاط التوجيه الخلفي الأيمن - حزمة ما بعد البيع
BYDYuan PLUS/Atto 3
2024شفّاط التوجيه الخلفي الأيمن - حزمة ما بعد البيع دليل الورشة — BYD Atto 3
Rear Right Steering Knuckle Assembly - Removal and Installation
Removal
- Remove the rear right brake mudguard. Refer to Right Rear Brake Mudguard - Removal and Installation
- Remove the rear suspension right trailing arm assembly. Refer to Rear Suspension Right Towing Arm Assembly - Removal and Installation
- Remove 1 fixing bolt, and put aside the floor wiring harness.

- Remove 1 fixing nut/bolt from the rear right steering knuckle and the rear right shock absorber assembly.

- Remove 1 fixing nut/bolt from the rear right steering knuckle and the upper right arm assembly of the rear suspension.

- Remove 1 fixing nut/bolt between the rear right suspension lower arm assembly and the rear right steering knuckle.

- Remove the rear right steering knuckle.

- Remove 1 fixing nut.
- Detach the rear right suspension control arm assembly, and take out the rear right knuckle.
Installation
- Install it in the reverse order of removal.
- Implement four-wheel alignment after installing the rear steering knuckle. Refer to Four-Wheel Alignment
Left Rear Steering Knuckle - Removal and Installation
Removal
- Remove the left rear brake mudguard. See Left Rear Brake Mudguard - Removal and Installation
- Remove the rear suspension left towing arm assembly. See Rear Suspension Left Towing Arm Assembly - Removal and Installation
- Remove 1 fixing bolt, and put aside the floor wiring harness.

- Remove 1 fixing nut/bolt from the left rear steering knuckle and the left rear shock absorber assembly.

- Remove 1 fixing nut/bolt from the left rear steering knuckle and the upper left arm assembly of the rear suspension.

- Remove 1 fixing nut/bolt between the left rear suspension lower arm assembly and the left rear steering knuckle.

- Remove the left rear steering knuckle.

- Remove 1 fixing nuts.
- Detach the left rear suspension control arm assembly, and take out the left rear knuckle.
Installation
- The installation steps are opposite to the removal steps.
- Implement four-wheel alignment after installing the rear steering knuckle. See Four-Wheel Alignment



