مجموعة خرطوم الفرامل الخلفي الأيمن
أكواد OE / المواد
13434542-00SC2E-3561040Bماذا يحدث بعد ذلك:
- راجع اختياراتك في صفحة السلة.
- ادفع مباشرة عبر Stripe (عندما تكون كل العناصر بأسعار التجزئة).
- أو أرسل القائمة كطلب عرض سعر للجملة.
المواصفات الفنية
- موديل السيارة
- BYD Atto 3
- تكوين التوجيه
- مقود يسار ومقود يمين
- الفئة
- فرامل
الشحن والإرجاع
شحن عالمي من الصين جواً أو بحراً. التسليم القياسي 5–30 يوم عمل، السريع 2–10 أيام عمل. تحسب تكلفة الشحن عند الدفع.
نافذة إرجاع 7 أيام للقطع غير المستخدمة في عبوتها الأصلية. تواصل معنا قبل إرجاع أي قطعة.
السيارات المتوافقة — مجموعة خرطوم الفرامل الخلفي الأيمن
مجموعة خرطوم الفرامل الخلفي الأيمن دليل الورشة — BYD Atto 3
Right Rear Brake Hose Assembly - Removal and Installation
Removal
- Set the intelligent power brake system assembly to "installation mode". See Installation Mode of Intelligent Power Braking System
- Remove the right rear wheel assembly. See Wheel Assembly - Removal and Installation
- Discharge brake fluid. See Replacement of Brake Fluid
- Remove 1 fixing bolt from the right rear brake hose assembly, and take out the bolt gasket.
- Remove the right rear brake hose assembly.
- Remove 1 brake line built-in bolt.
- Detach the metal clip, and take out the right rear brake hose assembly.
Caution The brake fluid has a strong corrosive effect on the paint. If it is accidentally splashed on the paint of the vehicle body, it must be cleaned with a rag as soon as possible. Avoid oil contact with skin. If it is accidentally splashed into the eyes, immediately rinse with plenty of water and seek medical attention as soon as possible. Do not discharge the oil at will, and recycle it according to local regulations.
Caution Place a collection container under the rear brake hose assembly to collect brake fluid. As the bolt gasket is deformed after the first installation, it cannot be used again. Replace the bolt gasket with a new one.
Installation
- The installation steps are opposite to the removal steps.
- Fill the brake fluid and bleed the brake system of the right front wheel. See Air Discharge of Braking System
Caution After the installation, press the brake pedal several times to ensure that the brake system works normally. Perform road test for inspection.
Left Rear Brake Hose Assembly - Removal and Installation
Removal
- Set the intelligent power brake system assembly to "installation mode". See Installation Mode of Intelligent Power Braking System
- Remove the left rear wheel assembly. See Wheel Assembly - Removal and Installation
- Discharge brake fluid. See Replacement of Brake Fluid
- Remove 1 fixing bolt from the left rear brake hose assembly, and take out the bolt gasket.
- Remove the left rear brake hose assembly.
- Remove 1 brake line built-in bolt.
- Detach the metal clip, and take out the rear left brake hose assembly.
Caution The brake fluid has a strong corrosive effect on the paint. If it is accidentally splashed on the paint of the vehicle body, it must be cleaned with a rag as soon as possible. Avoid oil contact with skin. If it is accidentally splashed into the eyes, immediately rinse with plenty of water and seek medical attention as soon as possible. Do not discharge the oil at will, and recycle it according to local regulations.
Caution Place a collection container under the rear brake hose assembly to collect brake fluid. As the bolt gasket is deformed after the first installation, it cannot be used again. Replace the bolt gasket with a new one.
Installation
- The installation steps are opposite to the removal steps.
- Fill the brake fluid and bleed the brake system of the right front wheel. See Air Discharge of Braking System
Caution After the installation, press the brake pedal several times to ensure that the brake system works normally. Perform road test for inspection.
