المجموعة الفرعية لملقط الفرامل الأمامي الأيمن
أكواد OE / المواد
13844713-00SC2EM-3501220ماذا يحدث بعد ذلك:
- راجع اختياراتك في صفحة السلة.
- ادفع مباشرة عبر Stripe (عندما تكون كل العناصر بأسعار التجزئة).
- أو أرسل القائمة كطلب عرض سعر للجملة.
المواصفات الفنية
- موديل السيارة
- BYD Atto 3
- تكوين التوجيه
- مقود يسار ومقود يمين
- الفئة
- فرامل
الشحن والإرجاع
شحن عالمي من الصين جواً أو بحراً. التسليم القياسي 5–30 يوم عمل، السريع 2–10 أيام عمل. تحسب تكلفة الشحن عند الدفع.
نافذة إرجاع 7 أيام للقطع غير المستخدمة في عبوتها الأصلية. تواصل معنا قبل إرجاع أي قطعة.
السيارات المتوافقة — المجموعة الفرعية لملقط الفرامل الأمامي الأيمن
المجموعة الفرعية لملقط الفرامل الأمامي الأيمن دليل الورشة — BYD Atto 3
Right Front Brake Caliper Body Sub-Assembly - Removal and Installation
Removal
- Set the intelligent power brake system assembly to "installation mode". See Installation Mode of Intelligent Power Braking System
- Remove the right front wheel assembly. See Wheel Assembly - Removal and Installation
- Discharge brake fluid. See Replacement of Brake Fluid
- Remove one fixing bolt and detach the right front brake hose assembly.
- Remove 2 fixing bolts, and take out the right front brake caliper sub-assembly.
Caution The brake fluid has a strong corrosive effect on the paint. If it is accidentally splashed on the paint of the vehicle body, it must be cleaned with a rag as soon as possible. Avoid oil contact with skin. If it is accidentally splashed into the eyes, immediately rinse with plenty of water and seek medical attention as soon as possible. Do not discharge the oil at will, and recycle it according to local regulations.
Installation
- The installation steps are opposite to the removal steps.
- Fill the brake fluid and drain the brake system of the right front wheel. See Air Discharge of Braking System
Caution After the installation, press the brake pedal several times to ensure that the brake system works normally. Perform road test for inspection.
Left Front Brake Caliper Body Sub-Assembly - Removal and Installation
Removal
- Set the intelligent power brake system assembly to "installation mode". See Installation Mode of Intelligent Power Braking System
- Remove the left front wheel assembly. See Wheel Assembly - Removal and Installation
- Discharge brake fluid. See Replacement of Brake Fluid
- Remove one fixing bolt and detach the left front brake hose assembly.
- Remove 2 fixing bolts and take out the left front brake caliper body sub-assembly.
Caution The brake fluid has a strong corrosive effect on the paint. If it is accidentally splashed on the paint of the vehicle body, it must be cleaned with a rag as soon as possible. Avoid oil contact with skin. If it is accidentally splashed into the eyes, immediately rinse with plenty of water and seek medical attention as soon as possible. Do not discharge the oil at will, and recycle it according to local regulations.
Installation
- The installation steps are opposite to the removal steps.
- Fill the brake fluid, and drain the brake system of the left front wheel. See Air Discharge of Braking System
Caution After the installation, press the brake pedal several times to ensure that the brake system works normally. Perform road test for inspection.
