مجموعة حزام أمان المقعد الأمامي الأيمن
أكواد OE / المواد
13465320-00SC2EM-5811020ماذا يحدث بعد ذلك:
- راجع اختياراتك في صفحة السلة.
- ادفع مباشرة عبر Stripe (عندما تكون كل العناصر بأسعار التجزئة).
- أو أرسل القائمة كطلب عرض سعر للجملة.
المواصفات الفنية
- موديل السيارة
- BYD Atto 3
- تكوين التوجيه
- مقود يسار ومقود يمين
- الفئة
- مقاعد وأحزمة الأمان
الشحن والإرجاع
شحن عالمي من الصين جواً أو بحراً. التسليم القياسي 5–30 يوم عمل، السريع 2–10 أيام عمل. تحسب تكلفة الشحن عند الدفع.
نافذة إرجاع 7 أيام للقطع غير المستخدمة في عبوتها الأصلية. تواصل معنا قبل إرجاع أي قطعة.
مجموعة حزام أمان المقعد الأمامي الأيمن دليل الورشة — BYD Atto 3
Right Front Seat Belt Assembly - Removal and Installation
Removal
- Power off the low voltage electrical system. See Power-off and Power-on of Low Voltage Electrical System
- Remove the right B-pillar upper guard assembly. See Right B-Pillar Upper Guard Assembly - Removal and Installation
- Disconnect 1 connector of the right front seat belt assembly.
- Remove 1 fixing nut from the upper part of the right front seat belt assembly.
- Remove the right front seat belt assembly.
- Remove 1 fixing bolt.
- Remove 1 fixing bolt, and take out the right front seat belt assembly.
Caution When disconnecting the connector, insert the small screwdriver wrapped with tape into the connector slot to pry up the striker, and then pull out the connector.
Installation
- The installation steps are opposite to the removal steps.
Caution After installation, check whether the seat belt is installed in place to ensure that there is no distortion or seizure.
Right Front Seat Belt Buckle Assembly - Removal and Installation
Removal
- Remove the driver seat assembly. See Driver Seat Assembly - Removal and Installation
- Detach 3 wiring harness clips from the right front seat belt buckle assembly.
- Remove one fixing bolt and take out the right front safety belt buckle assembly.
Installation
- Follow the removal steps in reverse order to install.
Left Front Seat Belt Assembly - Removal and Installation
Installation
- Power off the low voltage electrical system. See Power-off and Power-on of Low Voltage Electrical System
- Remove the left B-pillar upper guard assembly. See Left B-Pillar Upper Guard Assembly - Removal and Installation
- Disconnect 1 connector of the left front seat belt assembly.
- Remove 1 fixing nut from the upper part of the left front seat belt assembly.
- Remove the left front seat belt assembly.
- Remove 1 fixing bolt.
- Remove 1 fixing bolt, and take out the left front seat belt assembly.
Caution When disconnecting the connector, insert the small screwdriver wrapped with tape into the connector slot to pry up the striker, and then pull out the connector.
Installation
- The installation steps are opposite to the removal steps.
Caution After installation, check whether the seat belt is installed in place to ensure that there is no distortion or seizure.
مجموعة حزام أمان المقعد الأمامي الأيمن مخطط التركيب — BYD Atto 3
