وكالة
BYD Atto 3

مجموعة مقبض الباب الأمامي الأيمن

أكواد OE / المواد

13451191-00SC2EM-6105109
$18USD
متوفر
التوفّر بحسب الجودة

ماذا يحدث بعد ذلك:

  • راجع اختياراتك في صفحة السلة.
  • ادفع مباشرة عبر Stripe (عندما تكون كل العناصر بأسعار التجزئة).
  • أو أرسل القائمة كطلب عرض سعر للجملة.

المواصفات الفنية

موديل السيارة
BYD Atto 3
تكوين التوجيه
مقود يسار ومقود يمين

الشحن والإرجاع

شحن عالمي من الصين جواً أو بحراً. التسليم القياسي 5–30 يوم عمل، السريع 2–10 أيام عمل. تحسب تكلفة الشحن عند الدفع.

نافذة إرجاع 7 أيام للقطع غير المستخدمة في عبوتها الأصلية. تواصل معنا قبل إرجاع أي قطعة.

مجموعة مقبض الباب الأمامي الأيمن دليل الورشةBYD Atto 3

Right Front Door Outer Handle Assembly - Removal and Installation

Removal

  1. Lift the right front door glass to the limit position.
  2. Remove the right front door sealing plug I. See Right Front Door Sealing Plug I - Removal and Installation
  3. Take out 1 screw cover, and loosen 1 fixing screw of the right front door outer handle assembly.
  4. Disconnect 1 connector of the right front door outer handle assembly.
  5. Detach 1 fixing clip.
  6. Take out right front door outer handle assembly.
  7. Detach 1 fixing clip, and detach the left front door lock cylinder lever from the vehicle lock cylinder key assembly.
  8. Take out the vehicle lock cylinder key assembly.
  9. Remove 1 fixing screw of the right front door outer handle seat assembly.
  10. Remove the right front door outer handle seat assembly.
  11. Detach 1 fixing clip, and detach the right front door lock outward-opening lever from the right front door outer handle seat assembly.
  12. Take out the right front door outer handle seat assembly.

Installation

  1. The installation steps are opposite to the removal steps.

Right Front Door Handle Box Cover Plate- Removal and Installation

Removal

  1. Pry up the right front door handle box cover.

Caution Be careful when removing the trim panel to avoid scratching the surface material.

Installation

  1. The installation steps are opposite to the removal steps.

Right Front Door Snap Handle Ambient Light Assembly - Removal and Installation

Removal

  1. Remove the right front door guard assembly. See Right Front Door Guard Assembly - Removal and Installation
  2. Remove the right front door snap handle ambient light control module.
  3. Disconnect 1 connectors.
  4. Remove 2 fixing screws, and take out the right front door snap handle ambient light control module.
  5. Remove 3 fixing screws, and take out the right front door inner snap handle.
  6. Remove 2 fixing screws, and put aside the right front tweeter horn.
  7. Remove 1 fixing screws.
  8. Pry up the right front door inner snap handle seat and the handle.
  9. Remove 2 fixing screws, and take out the right door inner snap handle inner plate.
  10. Take out the right front door inner snap handle ambient light and the tweeter horn.

Install

  1. The installation is performed in reverse order of removal.